All Posts

screams nicely :D

100 gritty sound

Check "Befaco Noise Plethora" for noise

combined with a "Befaco Percall" you can do nice rhyhtmic noise patterns

EDITED May 7th, 15:25

depends on how you use it.
I have both next to each other and think they compliment well as a combo for granular clouds and glitches.
But its a matter of taste.
Beads can do much stuff other modules can do, but I think mostly you can not apply all these functions at once.
I use Morphagene to sample and mangle my modular sounds live, which adds some tape glich and beatslicing - and send it into Beads to add more texture and ambient clouds.
I like Morphagene because it´s very hands on.

Where is the noise in your fx / noise rack?
Maybe add a nice noise source?

-Intelijell Sealegs could be intersting for you.
Delay / reverb with saturation and noise

or
-Qu-bit Nautilus
-Make Noise Mimeophon

Maybe drop that Echoez?
Maybe a smaller and more vesetaile LFO like Batumi or Ochd+Expander?

Do you need the Cosmix?

Sorry if it's already been requested but I really would like to see:

1. "Pin" button on modules to lock an individual module to its place in the row. Like "Rack Lock" but on a per-module basis. There are some modules that I never want to see bumped or swapped until I'm ready. Probably would need some logic programmed for how it would interact with functions like the "push left/right" and row swap.

2. Link adjacent modules. Like pinning, above, only to another module. Use case: Link a module and its expander(s) and move them as a group. Link a series of modules always used in a chain, and move them around like a block. "Pin" a selection of "linked" modules to their spot on the row, and they will be impervious to accidental swaps and shuffles.

I'd be interested too as I have a couple ready to go

This is just a fun jam I did a few weeks ago. Love both of these combos:

Is that not a little too close to Beads?

Make Noise Morphagene

Just a spontanous thought :D

Hi

This is my current ambient / noise rack

The A-143-4 does alot of the modulation with Beads doing both granular and VCO. Endless Processor for external instruments / tape-lopps etc. It's simple but very effective and versatile

What should I fit into the 20HP?

I composed this ambient piece for a friend who had to be hospitalised. Instead of sending him a postcard Estroe and I decided to each create a piece of music for him. In my case this is the result. It’s called From the ground up. I asked my friend if I could share this piece with you and he immediately said: “Yes music and art needs to be shared. So please enjoy this ambient piece. May it soothe and comfort you

is there a section to advertise eurorack cases / racks for sale?

Really like the Dual Dagger - easy to get great sounds. Independent low and hi pass filters and CV panning. Great stuff.

I do use the 100 Grit as a filter (and it's awesome), but mostly I use the C4RBN and the Dual Dagger as filters and use the 100 Grit as distortion. The 100 Grit also doubles a great voice too - very flexible.

The Vult Freak looks amazing! Haven't looked at Ghost. Good luck with your decision :-)

A quick update:

6 weeks after, I still received no module from @sugarfreedaddy

he replies to messenger messages.
he said that he will refund me "asap" but that he currently does not have the money. I don't believe him whatever he says :D

He said that he is not home and can't ship (but he keeps on posting new ads here and on ebay for you people to buy :D )

For several reasons:

6 weeks no module received
he refuses to communicate his name or adress
he ships modules from Poland but his ads claim that he is in Germany
when he ships, he does not communicate his own name and no phone on the parcel... he ships without name...

For all those reasons I believe that he is a real scam and as such, I really want to state it clearly, hoping to help modulargrid people: this guy is here to scam.

No drama please.

Happy patching everyone :D

This person is indeed selling on several platform and scamming people.

He is selling and refuses to provide name or adress, even to buyers.
He ships parcels with no name, no phone.
He ships from Poland but advertises being in Germany.

In my case, I paid with Paypal to family, he kept the money and never sent the module, this was more than 6 weeks ago.
This has been reported in the bad trader thread too.

Hi there,

Got a chance to put my hands on the ne Neo Trinity of Bastl Instrument, a rich modulation source x 6 with plenty of options.

Tryin' to make my video visible on the youtube section but it fails, so I thought I could publish here. It's all in French with subtitles.

EDITED May 6th, 05:23

Awesome.
This is excactly what I have been looking for.

Im very happy about this :D
Thank you so much

Wow didn't see that Thought u only had the 100 grit in there
What is you thoughts on the dual dagger?
I am eyeing it as well but i'd really want a vult freak.
Sadly not readily available so ...
The endorphin ghost looks like a very nice filter as well. Hard decisions m8

For my part I am already equipped, but I must admit that it is a good concept.

Morning jam...

I predict everyone is going to want one of these.
Looks the perfect addition to a percussion rack or ambient with long samples.

Hi @Chrissozz. The Dual Dagger is a stereo filter: it pairs really well with the Chainsaw

Just asking a question here ... The chainsaw is a stereo oscillator yeah?
Your filters are mono tho. Wouldn't you want at least 1 stereo filter to go with the chainsaw?

This patch attempts to create the appearance of multiple voices from just one by only occasionally sending a note to the delay. A second voice can be added, tuned to a perfect 5th of the primary voice to add a little more depth.

Before getting started, tune the top oscillator to a C, and the bottom to a G.

The Rene's X channel is used to sequence the frequency of both oscillators. The X channel gate triggers the envelope for the primary voice, going to the dry channel. Use a slower Tempi clock to The Y channel or a more sparse gate pattenrn to trigger a second envelope which controls when the oscillators get sent to the Mimeophon.

For best results, keep Mimeophon clock to same tempo as X-channel, and Rate at noon.

Listen to the result on the output of VCA channel 4, rather than mimeophon like you normally do.

Play with:
- envelopes
- gate patterns on X and Y channels
- clock speeds to the Rene
- Access page of X and Y channels to create sequences of varying lengths
- Mimeophone Zone, Repeats, and Halo

This patch attempts to create the appearance of a wide range of voices from just one voice, by modulating waveform/timbre and how often it's sent to the delay. A second voice is occasionally brought in tuned to a perfect 5th of the primary voice.

Before getting started, tune the top oscillator to a C, and the bottom to a G.

The Rene's X channel is used to sequence the frequency of both oscillators. The X channel gate triggers the envelope for the primary voice, going to the dry channel. Use a slower Tempi clock to The Y channel or a more sparse gate pattenrn to trigger a second envelope which controls when the oscillators get sent to the Mimeophon. The Y channel CV also modulates the waveform from sine to saw on the oscillator. C channel CV gets mixed with the Y channel's envelope, using Maths sum output, to modulate how much of the second oscillator (perfect 5th) gets sent to the mimeophon.

For best results, keep Mimeophon clock to same tempo as X-channel, and Rate at noon.

Play with:
- envelopes
- clock speeds to the Rene
- gate patterns on X and Y channels
- CV on Y and C channels
- Mimeophone Zone, Repeats, and Halo

EDITED May 4th, 19:18

Any news? I need this! Today! Please Scott, you still have a few hours left today, 4th of May, 2024... just drop one ... thanks, big hug from Budapest

mother 32: Eb6sus2\C (Cminor) + Bb6sus2\G arpeggio
subharmonicon: cut off, vcf decay, vca attack
dfam: noise, vca decay
1.intro vessel noise and drum kick, mother 32 play manual
2.dfam starts + mother 32.
3. Enters SubH.
4. change noise dfam.
5. only dfam+subH.
6. enters mother32 fatty + new drum.
7. closing with sam vessel sound.

add drone sounds. add drum machine

EDITED May 4th, 12:46

Thank YOU both, yes, Marbles - shes such a player! :-)

Care for another?

Cheers!

ah ok

thanks for info

That's a Unicorn account feature, max HP for free users is 168, but it's 432 for Unicorns: https://modulargrid.net/e/users/pro_index

Good stuff.

Good stuff.

Beautiful walk in the Plonk Gardens in the company of King Marbles.

Hello,

this guy: https://modulargrid.net/e/users/view/231400 offered also on Ebay Kleinanzeigen. After requesting personel contact, I received no response. Therefore I informed Kleinanzeigen and all offers are now deleted, including the profile.

EDITED May 4th, 05:10

hi there

it is Impossible to make a "ADDAC 901TAM" with 197 HP per row

the max is 168 HP and i need 197 HP...

can you help me ??

thanks

[]

So the puroose if this isnt to be thee most rational or even functional system, but mire to just motivate me to create.

The hardest part of art for me is just getting the motivation and emotional energy to "do".

I have ADHD, so what ever tool or instrument i use has to be instantly gratifying to the eyes and it must be tactile and kinetic... ir else I din't get the dopamine hit

Enjoy!

ahh lovely - that'll work thanks so much @modulargrid

yeah seems so - hopefully @modulargrid can sort something
-- greenfly

no CSV, but Unicorn users can get XML and JSON formats by adding .xml or .json to their rack url.

yeah seems so - hopefully @modulargrid can sort something

No worries then, was just giving you an option seeing as there doesn't look to be what you are asking for.

no, I would like a nicely formatted csv file - like you would get from a sql query.

Hi all,
finally release 0.3.0 is available!
- Arpeggiator Track
- increase stochastic rest proability to 15 steps
- logic track fast input visulaization (press shift)
- fix clipboard copy track
- fix logic gate probability
- fix rotate steps (thx to glibersat)
- keep sequence names when copy and paste
- issue #100 - reorganize quick functions shortcuts
- issue #101 - reset cv in stop parameter
- integrate Malekko integration
https://github.com/mebitek/performer/releases/tag/0.3.0
from now on there will be no more major upgrades but just bufixes and workflow improvements. feel free to open issues on github both for bugs and for workflow ideas.
as always rate the project on github and feel free to donate to support the project:
https://mebitek.bandcamp.com/
https://liberapay.com/mebitek
thanks to all tester Jil, Guillaume Libersat, XQSTKRPS, P.M. Lenneskog

Click the Data Sheet link below your rack, copy and paste the page into something.

Can I get a csv file of my racks - is there an export option?

Dear all,
I plugged an usb hub like this https://www.amazon.it/gp/product/B06X8Z86VP/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 to power arturia beatstep pro with the power supply of my doepfer A-100 diy psu. https://www.doepfer.de/a100_DIY_kits.htm#A-100%20DIY%20Kit1
With arturia keystep37 seems to work but with beatstep pro the other modules doesn't work well.
I connect +12V and -12V correctly to A100 psu
https://storage.googleapis.com/modulargrid.net/easymde/185440_d081e7eec60e97f210c019a899702f5e_1714581078.png
but probably the beatstep pro drain too much power. If I use tubbutec usb bridge A in my other rack with doepfer A100-psu3 it works, obviously with 2A instead of 1.2A, I have more resource.
I have 1A free for main rack with psu3

and for the other rack with psu diy I have only 0.4 A free

Do you have any suggestions? Is possible to use Klavis No Drain to recover extra +12V from unused 5V (but if I remember well it converts -12V to 5V so in this situation is useless)?
A voltage converter would be needed to use 5V instead of 12V (like tubbutec does) but A100-diy psu doesn't have 5v.
"Nothing created and nothing destroyed" I thermodynamics rule but maybe I'm missing something...
Thanks
FB

EDITED May 1st, 22:12

Does anybody know where I can find the BraidsIllustrated guide? I used to be able to google it. It is really cool whoever created it. There used to be a link on Youtube from DivKids review of Braids but that link is now underconstruction. It seems like it has been scrubbed from the internet. If that is even possible?

mostly for creating more complex, but related versions of modulation sources (& for attenuating them at the same time)

As above!

I have the SSM which can also be used as a kind of patch memory too.